Category: Tractor Maintenance

Hydraulic Fluid & Etc.

I pushed it off till the end of the day, but I finally changed the hydraulic fluid in the tractor! I have been a bit nervous about it for some time. But when it came to actually doing it, it really was not hard at all. So that is done and seems to be working great. It is at the highest possible level before it is considered overloaded, but I can either remove a bit, or even let it be for a bit and see how it pans out. I may pull a little through the transmission drain, a small one under the middle rear of the tractor and let just a bit escape. It depends on the weather, and if it is reachable without getting into more mud than I had to today just to do the fluid and filters.

So, in total, over the last two days I have changed the oil, the oil filter, the fuel filter, and cleaned the air filter, then changed the hydraulic fluid filter and the high-pressure hydrostatic filter, and the hydraulic fluid on the tractor. I also topped up the coolant/anti-freeze. Only things left to do is put a piece of cardboard in front of the radiator and get winterized diesel for it. Oh, and finish cleaning the glass. Oh, and maybe look at changing out that front axle fluid.

I also got up on the roof today and cleaned the chimney. As usual, that went easy. I came down when it was swept all the way down and cleaned out the stove pipe and the stove, and the bend in the chimney. It was pretty easy, especially as I have everything set up for an easy clean. I even know the one wrench I need up top is a 7/16ths inch box end. At the bottom a slot and a Phillips screwdriver do the job of getting everything apart on the stove pipe. Again, easy!

We did a bunch of pre-Christmas cleaning today. I also went to the store and got more stuff for the big day on Monday. Also made sure to have everything needed to get through with the stores being closed an extra day over the weekend.

So, today was a really good day! I cannot believe I got through it without much pain at all. I cannot believe how much I got done, especially as compared to my normal run of the mill day. Usually, the arthritis has me stopped by the time I would have finished my part in the house cleaning. In fact, I did take three Advil towards the end of that. I guess it really helped.

Back to School

We have been so busy getting so little done lately. Sometimes that’s how things seem to go. There is a lot that needs to be done, and there is a lot that we are doing. But does it feel like we are getting caught up? No. I guess that’s just the way things go.

We got the girls registered for their respective schools yesterday. Our youngest has not been in public school before, and the oldest has not been in for the last five years or so. Hopefully this is a good choice for them. We got them into a district next to our catchment area where the classes will be smaller and they should have the opportunity to know everyone well, and for their teachers to give them the attention they should be getting in an educational setting.

So that is the close of an era for me. I have had a kid at home for homeschooling every year since 2006. Seventeen years! Now, at 52, I have to get things together and figure out what I want to be when I grow up. I have till a week from next Monday.

Also yesterday, I went out to check the feed in the chicken coop, and saw there was a dead peachick on the floor. The mamma bird was not sitting on eggs anymore by the door. Why she had to nest right in front of the door escapes me. I saw her in the back corner of the run, and walked over. Every bird scattered but her. She stayed sat. I hated to do it, but I got her to get up and reveal a day-old chick. The other appeared to be three or four days old, at least. So, to prevent another loss, I gathered the chick and took it into the house where we set up a box and put it in for the night. It will have to be caged separately to prevent it being run down like the other one appeared to have been. I can see it going out again in a couple of months, when it is big enough to stand up to a flock of chickens. It only needs to be as big as a hen. The hens usually don’t bother with the peafowl the way they will do bullying another chicken. As much as I hated to separate the mother and chick, there is no better way.

My latest shop project has been a simple one. I have assembled a stitch pony so I can do some leatherworking at the work bench. It is a simple one, designed to clamp under the force of the bench vise. All I have left to do is get some tacks and put some leather pads into the jaws of the pony, then I can use it freely.

The tractor is running low on hydraulic fluid. It has a leak in one of the pistons on the loader. Honestly, it is a little depressing. Who wants to have to put it in for service. How long will they keep it for? But at least I know why the bucket has been drooping or reacting a little slow, I think. I think I know. I don’t know for sure, but when I tightened the hose to the piston, it acted a bit better. It just continues to leak, and I think I may be a bit tight on the crush washer and want to have a tech service it correctly. Maybe they can do it onsite. Or maybe they can just take the loader, if they have to. Then I can continue to use the rest of the tractor here for some jobs. I think I am a bit spoiled having had that tractor to do my heavy lifting for me!

Well, it is nearly 3AM, and I need to get back to sleep. Or at least try.

Water Levels Going Down!

It is snowing as I type this. The forcast calls for less than 2 inches total. What’s more, the water in every pond, puddle, and place water can sit on our property has gone down by maybe three inches or so since yesterday. Then, apart from a splash of rain forecast for Monday it is at worst partly cloudy skies for the coming week or more. So I am not going to let myself feel as though we are getting any consequential setbakcs with what will fall. Not to compare this to a glass is half full situation as in our case, the glass is finally half empty, and things are improving as it goes down!

What’s more, I recieved the hydraulic toplink for the tractor this morning. There is some prep work to do to it before I put it on the tractor. It is a simple installation, so it should be easy. That will allow me to change the angle of attack on the boxblade, allwing me to either dig into, or smooth out the mud. I would prefer to smooth it. It shoudl also improve the angle when using the scarifiers to pull rock up on roadbase or gravel drives. Not that I have any, or anywhere near enough.

The winter storm advisory is now replaced with a precipitation alert that goes till 1:00PM, so there’s no telling that will really come of it, but I don’t think much.

End of February Update.

It is definitely still winter here at the farm. We have good chances of snow for most of the coming week. Looks from the weather radar that whatever does come will likely have to form, as nothing closer to the west coast seems to be heading our way. It was warm today, though! We got up to 38F according to our weather station.

The SDR Radio I got the other day worked as expected. I got it running that day and played around with it, then delivered the second one to the desktop computer upstairs but did not yet set that one up. It’s fascinating how it can read or see the whole spectrum, and portions of it visible at once to tell where different signals are and have a hint to what kind they are. FM Radio signals are amazing, especially where they have digital encoding on both sides of the frequency. Even stations without that digital encoding are amazingly powerful compared to the rest of the spectrum. I will have to work on reception and an improved arial.

The tractor reached 200 hours yesterday. That’s just shy of five months! I cannot believe we are coming up to five months of ownership already! It still seems new to me. Most of its work here has bene snow clearing, but as soon as the weather breaks to spring, I think it will see a total shift! I may move big snow piles into the orchard just to get the trees started for the year. I may have to move a lot of hay off the garden and start it for tilling. I want that space tilled four or more times prior to planting in May and June. There will be post holes to dig, too. I am going to have to reset some fencing and clear some old areas out. Then there is the firewood. I don’t expect to muck about with that this year, since I want to be two years stored by autumn, and since I want to have a load of wood to work with. I hope to see this whole area of my chores severely altered to what it has been in previous years.

I got the second GoPro camera that I have been thinking about. If I am going to do a YouTube channel, then this setup I have is good enough to do it with. I would benefit from a lavalier mic, but I have a separate sound recorder that can also do the trick for now. I’ll have to give it a try. I am having a card reader delivered so I can put one on my laptop and one on my desktop to unload videos and edit. I have tried out the GoPro cloud, and I am not terribly thrilled with any of it, apart from the discount they offer to users while shopping. I’d rather keep the filed local, I think. Then I’ll only upload final cuts to the Internet. I have yet to see any real advantage apart from having apparently all the space I need to keep every crap video file I make. That may turn out to be the seeds of a problem. But who knows? Maybe in the next few weeks I’ll get a video created and uploaded to the channel again.

Mondy is anticipated to be the day we have our deli slicer delivered. I have been wanting a proper one for many years now, and we have what appears to be a decent one on the way. It is a Berkel 300 Redline. I am a little worried about it after seeing the shipping details. For whatever reason, it is listed with a shipping weight of 122 pounds. I am having trouble believing that, but I worry that I believe wrong. I guess we’ll see what it is like when it gets here. But honesty, how can a home line slicer weight so much? Maybe they packed it in a wooden crate?

I have very few hand tools left in my wish list now. A shipment arrives also on Monday. It is just a few things, and while there are a couple more planes to be desired, I think I have enough to get a real start in my workshop. Spring will give us access to the barn for cleanup, and to rearrange our storage. I have a permanent wall to fix into the old garage door of my shop. That wall wants a window built into it for some heat and light. Missus has a kiln on order that also wants a home in the shop.

So, a lot is going on this year. I think we will be able to reach closer than ever to self-sufficiency. I have always said that it is a very expensive state to reach. On the upside, I am where I can start building some of the remaining tools I need. I am even considering building my own travishers. I’ll still have to buy the blades, but the handles and bodies will save me around $100 each. That’s not small potatoes. Small potatoes come from my garden.

There you have it! An end of February summary. That’s what’s going on, and where we are at, and where we are going for the moment. I am excited to be at the point in life where I feel like I finally have a life, and all the things that that entails. Having moved country twice and other events that have left me with next to nothing, it is a hard thing to recover from. But I feel quite like I have arrived. Everything else is just improving things up and building equity. For me, that’s a good place to be. Oh, and I am about two weeks short of my 52nd birthday.